White balance settings for ASI224MC

any question related to our SDK and driver

Moderators: yang, chad, ray

Post Reply
Tulloch
Posts: 3
Joined: Tue Dec 03, 2019 12:50 pm

White balance settings for ASI224MC

Post by Tulloch » Thu Dec 05, 2019 11:45 am

Hi there, I have been using an ASI224MC for a few months now to image the planets and it’s working really well, thank you for developing this product. One thing I’ve noticed while imaging is that I need to make significant changes to the colour balance after capturing and stacking the frames, in particular the raw images come out too green. I am using FireCapture to take the images and use the recommended white balance settings of Wred=52 and Wblue =95, but I always need to increase the blue and red levels and decrease the green level in order to make the final images “correct”.

You can see the effect in my posting on the Cloudy Nights website below for examples.
https://www.cloudynights.com/topic/6853 ... -asi224mc/

Christophe Pellier recommends setting the Wblue value to 99 (the maximum) and even then it’s not high enough.
https://www.planetary-astronomy-and-ima ... camera.pdf

I spoke with Torsten who writes the FireCapture program and he is unable to program a Wblue value higher than 99 since the ZWO SDK does not allow for values greater than 99. So to get to the point (finally);

Can you please create a new SDK file for the ZWO cameras where the maximum Wred and Wblue values are (say) 150?

This way I can set a better white balance for the camera straight out of the box, without having to rely on modifying the colour settings after capturing.

Thanks for your consideration in this matter.

Andrew

User avatar
chad
Posts: 660
Joined: Thu Feb 09, 2017 4:58 am

Re: White balance settings for ASI224MC

Post by chad » Thu Dec 12, 2019 3:44 am

Hi Andrew,
Sorry, we can not.
First, as we know, what our SDK provides is a general method. So for the white balance, when you set to the max, the pixel value will be doubled to the original value, otherwise the minimum value will be only half. It is enough for most of the applications.
Second, although this operation seems simple, it is actually closely related to our entire architecture. So it is not an easy job to change it.
Third, I think it should be easy to do it in the applications than SDK, You just need to capture the original data, then proceed it according to your needs.
Thanks
Chad
ZWO Driver Engineer
Location:lon=120.6 lat=31.3
SuZhou China

Tulloch
Posts: 3
Joined: Tue Dec 03, 2019 12:50 pm

Re: White balance settings for ASI224MC

Post by Tulloch » Fri Dec 13, 2019 12:32 pm

Hi Chad, thanks for your reply.

It is a shame that the maximum setting cannot be (say) tripled instead of doubled, as this would enable us to set a more accurate white balance directly from the ASI224MC.

While this correction is relatively easy to apply in an application like FireCapture that uses the SDK, this would most likely introduce performance issues that would degrade the maximum capture rate which is a key feature of these cameras.

Thanks again,

Andrew

Tulloch
Posts: 3
Joined: Tue Dec 03, 2019 12:50 pm

Re: White balance settings for ASI224MC

Post by Tulloch » Mon Dec 16, 2019 12:01 am

The easiest way (I believe) to implement this would be a simple option to choose whether the multiple was 2 (giving min value of 0.5 and max of 2.0 which is the current setup) or 3 (giving a min value of 0.3333 and a max value of 3.0).

Just a suggestion :D

Thanks,

Andrew

User avatar
chad
Posts: 660
Joined: Thu Feb 09, 2017 4:58 am

Re: White balance settings for ASI224MC

Post by chad » Mon Dec 16, 2019 1:24 am

Hi Andrew,
If this operation is execuated in the application, it will not affect the camera, so the max framerate will not be reduced.
And for us, the resources are limited, so only the basic service can be provided. White balance is among them.
Hope you can understand.
Thanks
Chad
ZWO Driver Engineer
Location:lon=120.6 lat=31.3
SuZhou China

Post Reply